|
Size: 3644
Comment:
|
Size: 983
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| ''During the installation I noticed some [[Troubleshooting Disk IO|slow IO]], this was due to the use of btrfs. For this reason I use ext4. I want to switch back to btrfs, but need to find a proper solution first.'' | |
| Line 7: | Line 8: |
| == Network == | Configure the [[GlusterFS Server|servers]], then the [[GlusterFS Client|client]]. Once completed continue by setting up [[GlusterFS Encryption|encryption]]. |
| Line 9: | Line 10: |
| The GlusterFS servers will have fixed IP-addresses. That is configured in the DHCP servers list of statically assigned IP-adresses by using the Domains MAC address. * 192.168.1.40 gluster01 * 192.168.1.41 gluster02 * 192.168.1.42 gluster03 * 192.168.1.43 gluster04 == Disk == === Add hardware === We will add an additional disk to the system. This disk will be used for file storage. [[Domain Editing|Domain Editing]]. === Configure disk === ==== Partition ==== Create one large partition on vdb with partition type `8e Linux LVM`. ==== LVM ==== Set up a new physical volume and volume group {{{ pvcreate /dev/vdb1 vgcreate vg2 /dev/vdb1 }}} ==== LVM Volume ==== {{{ lvcreate --size 4G --name gluster_www vg2 }}} ==== Mountpoint ==== Create the mountpoint. {{{ mkdir /srv/www }}} ==== Format ==== Format the volume. {{{ mkfs.btrfs /dev/vg2/gluster_www }}} ==== fstab ==== Add the volume to `/etc/fstab`. {{{ /dev/vg2/gluster_www /srv/www btrfs defaults 0 0 }}} ==== Mount ==== Mount the new volume. {{{ mount /srv/www }}} If the mount command does not succeed, it it most likely because the fstab entry is incorrect. == Software == {{{ apt-get install glusterfs-server }}} from gluster01 connect with the other gluster servers {{{ gluster peer probe gluster02 gluster peer probe gluster03 gluster peer probe gluster04 }}} check server status {{{ gluster peer status Number of Peers: 3 Hostname: gluster02 Uuid: 031573c2-3b1f-4946-bd78-421563249db6 State: Peer in Cluster (Connected) Hostname: gluster03 Uuid: ff5cec1c-6d7f-4db7-8676-08deff06b4d0 State: Peer in Cluster (Connected) Hostname: gluster04 Uuid: 65fc398a-52e9-4292-9bbb-884becfbf5d6 State: Peer in Cluster (Connected) }}} create the gluster volume. the force option is needed because we are creating the volume on a mountpoint. {{{ gluster volume create www replica 4 transport tcp gluster01:/srv/www gluster02:/srv/www gluster03:/srv/www gluster04:/srv/www force }}} start the volume {{{ root@gluster01:/srv/www# gluster volume start www volume start: www: success root@gluster01:/srv/www# gluster volume status Status of volume: www Gluster process TCP Port RDMA Port Online Pid ------------------------------------------------------------------------------ Brick gluster01:/srv/www 49152 0 Y 826 Brick gluster02:/srv/www 49152 0 Y 1355 Brick gluster03:/srv/www 49152 0 Y 1034 Brick gluster04:/srv/www 49152 0 Y 1135 Self-heal Daemon on localhost N/A N/A Y 846 Self-heal Daemon on gluster02 N/A N/A Y 1377 Self-heal Daemon on gluster03 N/A N/A Y 1054 Self-heal Daemon on gluster04 N/A N/A Y 1155 Task Status of Volume www ------------------------------------------------------------------------------ There are no active volume tasks }}} |
If you only want to run 2 GlusterFS servers then setup [[GlusterFS Server with Arbiter|servers with arbiter]] and [[GlusterFS Client with Arbiter|client with arbiter]] instead. |
GlusterFS
During the installation I noticed some slow IO, this was due to the use of btrfs. For this reason I use ext4. I want to switch back to btrfs, but need to find a proper solution first.
GlusterFS is a distributed filesystem. It has built in redundancy, so it is possible to run two servers which automatically replicate files between the servers. If one server goes down, the other just takes over. Once it comes up again, files are automatically replicated. Here we will use GlusterFS as a redundant network mounted file storage.
For the sport of it, we will configure 4 GlusterFS servers.
Configure the servers, then the client. Once completed continue by setting up encryption.
If you only want to run 2 GlusterFS servers then setup servers with arbiter and client with arbiter instead.